1.Plug EasyDisk into the USB port, then you can find the "Removable Disk" in "My Computer".

2 Double click "Removable Disk" to access EasyDisk

3 You are free to operate all the files in your EasyDisk just as that in the local hard disk .

4 Write-protect Lock:

When the switch is in the state of unlock, you can carry out all kinds of operations such as write, format, change password etc. You can only read the files in it when EasyDisk is locked, which can prevent your data from being erased by accident.

5 Encrypt EasyDisk:

Note: Please keep the password in your mind after encryption, in case password forgotten, EasyDisk must be low-level formatted. All information in EasyDisk will be lost. Please refer to 8 for low-level format method.

a. Double click the "Passid" file (If this file not found, please copy it from directory "Utility\uti_dir" in CD Driver to EasyDisk.) or the Key icon in the bottom taskbar, press the "Yes" button in the prompted window.

b. Input your password into "New Password" bar, and reenter password into "Confirm New Password" to confirm it (the password can be consisted of letters, figures, underlines, spaces and all other characters on the keyboard, length of password can be up to 20 digits).

c. Press "Apply" button to confirm the password. You will be asked to input the password every time when accessing EasyDisk.

6 How to use password?

a. Insert EasyDisk into USB port, open "My Computer" and double click " Removable Disk" and access to EasyDisk.

b. Double click "Passid" or double click the key icon in the bottom taskbar, input your password into the blank of "Password" to access EasyDisk.

7 Decode your EasyDisk:

a. Double click "Passid" or double click the key icon in the bottom taskbar, select "Change Password"(Refer to the above picture).

b. Input your password in the blank of "Old Password".

c. Don't input any word into the blanks of "New Password" and "Confirm New Password"

d. Press "Apply" button, an information bar will prompt, press "Ok".

8 Low-level formatting function:

When you forget the password or need to clear all files in EasyDisk, you can use Low-level formatting function.

Note: Low-level formatting function will delete all files in EasyDisk.

You can operate as following:

a. Run the "UDReset" file under the folder named "Utility" in CD Driver, a DOS window occurs automatically, press "Y" then click any key. Pull EasyDisk out of the USB port (you can ignore this operation if your EasyDisk is unencrypted).

b. You can choose one of the two ways to format your EasyDisk :

I. Enable your EasyDisk password:

Insert EasyDisk and run the "Mformat" file under the folder named "Utility", select "Quick" and "Enable Password Feature" then press "Start" button, exit the procedure once the operation is finished.

Note : The password of EasyDisk will be the original one "1111' , you have to input the original password "1111" when using EasyDisk.

II. Disable password function:

Insert EasyDisk and run the "Mformat" file under the folder named "Utility", just select "Quick" then press "Start" button, after that please exit the procedure.

9.How to make the bootable EasyDisk?

You should use the low-level formatting command to make bootable EasyDisk (refer to 8), please backup your files and data in the EasyDisk before you making the bootable one in case losing it.

a. Windows 98/SE/ME Operating System:

a). Run the “UDReset"file under the folder name of “Utility" in Driver CD, a DOS window occurs automatically, press “Y" then click any key. Unplug EasyDisk out of the USB port (you can ignore this operation if your EasyDisk is unencrypted).

b). Insert EasyDisk again and run the “Mformat"file under the folder name of “Utility”, select “Quick"and “Make bootable disk”  then press “Start"button and exit the procedure , now your EasyDisk becomes bootable with other function not changed.

b. Windows 2000/XP Operating System:

a). Format a bootable 3.5"floppy disk under the operating system of Windows XP/ 98 /SE( Windows 2000 does not work as well). Then copy the file of 3.5"floppy disk to the Driver folder named “Utility/UTI_DIR”.

b). Run the “UDReset"file under the folder name of “Utility" in CD Driver , a DOS window occurs automatically, press “Y" then click any key. Pull EasyDisk out of the USB port ( you can ignore this operation if your EasyDisk is unencrypted).

c).Insert EasyDisk again and run the “Mformat"file under the folder name of “Utility”, select “Quick"and “Enable Password Feature" ( do not need to select it under Windows 2000 ) and “Make bootable disk "then press “Start"button and exit the procedure , now your EasyDisk becomes bootable with other function not changed.

c. Once EasyDisk becomes bootable, it will be the Drive A while floppy Drive will be Drive B under DOS.

10. How to use the bootable EasyDisk?

Note: EasyDisk only work as bootable one properly under the system whose BIOS support USB device booting function.

Insert the bootable EasyDisk into the USB port, and change the system setting "First Boot Device"into "USB-ZIP”, then EasyDisk can boot your system now.

11 How to use EasyDisk under the DOS system?

       Once your EasyDisk is bootable , then you can use it under DOS system ( EasyDisk is Drive A while floppy disk will be Drive B).

Note: When using the “Mformat"command to make the bootable EasyDisk, if you select “Enable password feature”, then you can only read files in EasyDisk under DOS system instead of writing in it ( because it is password protected). As for you have to select “Enable password feature"when you use “Mformat" to make bootable EasyDisk under Windows XP, so you can only read the file in the bootable EasyDisk which was made under Windows XP and can’t write files into it .